Search Results for ‘need help’

Hey guys my name is AJ and I am about to join the Kawasaki family as soon as I find the right bike! I know I’m new here but got a critical question. I am considering buying a used ZX6R 2021 3200 miles that shows a solid reddish/orange light on the right side of screen under the oil level...

Hey what's up good people! I’m new to this forum and motorcycle's, I have a 2022 Z400 ABS. Today I was in a hurry to get home, once i got home I turned off the bike and somehow didn't put the kickstand all the way down and dropped my bike. I lift it back up and check the damage and thought it...

I live in Indonesia and recently acquired a 2010 KLX150. Looks like it shares the same air box parts with the 140. Discovered the bike had no air filter, cage, partition, backfire screen, etc. So, I got all that stuff, but don’t know how the screen is normally attached from the factory??? Not...

Hi all, hope you're all well. I purchased g2 last January and she run like a dream for them most part. I serviced and done a general brush up to bring her back to former glory. after a long 70 mile intense ride about 10 minutes from home I was accelerating up a long straight through some...

Hi i just bought my first bike last night for like 700$ needs flashers mirror and cluste and a gas tank or a way to clean the gas tank from the rust, and i was doing some basic stuff to see if the engine was running took me an hour to make it start, but my question is about the transmission so...

When I removed my tires and took them to a shop someone use the back breaks (not on tire) and now I cannot loosen the caliper to get it back in the tire? Is there anyway to loosen it?

When I change my tires the back breaks got pushed and now the back caliper is closed and I cannot put it back on the tire? Is there anyway to loosen it so I can put it back on?

I have a 2019 ninja zx6r it has an upgraded exhaust Dino jet power commander and fuel Module to keep from getting error codes I have the servo buddy and o2 sensor on my exhaust. My problem started a few days ago I was driving when the ktrc, kqc, and the full power and lower power lights all...

Hello everyone !!this bike is new to me. wen i got it the clutch was wore out barely pulled the bike . so i replaced the plates toured the spring bolts to 17in pounds. put my rod back in. and it sets like the clutch lever should be pulled be for it gets any tension. I dont get it. It seems prity...

I have a 2005 Kawasaki Ninja ZX6R-636 and the bike was stolen from me twice which led to the thief's busting the ignition. I wired it up (with a 100ohm resistor) and I've ridden fine for a year now. A few days ago I rode to the store and when I went to leave the bike wouldn't start, now I'm at...

Hello as you can see in the image, the tire is uncentered or something?? Anyone know how i could fix this? I just replaced the tire and used the zip tie method but now its this and im stuck.

What tires do you guys find work well on a 2009 650?

Hi there, I am having issues with my cluster gauges and although I have found similar forums nothing has a definitive answer that has worked for me yet, so I am starting a new post in hopes someone can help me fix my issue. I have an 09' ZX-6R, just out of storage had it running perfectly last...

Hey guys, I’m doing my first total bike build, bought a 2009 Ninja 650R and I’m converting it from the street fighter style that the previous owner had to a fully faired street bike. It had an aftermarket headlight on it and I’d like to put the stock one back in, but I’m not sure what hardware...

I purchased the engine of a Kawasaki z1000 03 bike for a school project buggy, however, I have run into a few problems with the engine starting. I have the original harness from the original bike and the throttle bodies. I have wired up everything I can but I'm still having issues starting the...

A lot of lights are missing on the revcounter, the mechanics are saying it's due to water getting into the dash and damaging it. They say the only solution is to replace the entire dash, which is £800 with labour. Does anybody know another way to fix this? A couple of guys said the LED...

Hello guys, I have a 2003 636, need a front brake master cylinder, i'm trying to get a nissin MC but they have different "Bore size".....no idea about the right bore size of that bike, the owner's manual doen't say anything about that. Can anybody help me with that info or any advise about what...